Independent pressure-mapping evidence for HeelSafe and SoleSafe

This case study summarises an independent evaluation of two Prolevo pressure redistribution pads — HeelSafe (a leg-section inflatable heel overlay) and SoleSafe (a bed-end pad that sits between the sole of the foot and the footboard). The evaluation used objective pressure mapping to test performance across a range of body weights, positions and inflation settings.

Key facts

ProductsProlevo HeelSafe (leg-section inflatable heel overlay) and Prolevo SoleSafe (bed-end pressure redistribution pad)
ReportEvaluation of Prolevo HeelSafe & SoleSafe Pressure Redistribution Pads
Report authorDuncan Bain Consulting, Kings Langley, Hertfordshire
MethodUCL Phantom pressure-mapping (HeelSafe) and live-subject XSENSOR pressure mapping (SoleSafe and side-lying testing)
Comparators3 inflation settings (10, 20 and 30 mmHg); body weights from 40kg to 200kg; flat, knee-flexed and side-lying positions
Test conditionsSupplied 100 pairs of HeelPro Advance boots and provided ongoing clinical education and support
Commissioning & dateReport commissioned by TalarMade

The challenge

The heel and the sole of the foot are among the most common sites for pressure damage, and interface pressure at both sites varies considerably with mattress choice, patient bodyweight, positioning and even knee flexion. A foot resting directly against a mattress, or against a bed footboard in a supine position, can generate high interface pressures that are easy to overlook. Clinicians need pressure-relief products whose performance has been mapped objectively across this range of conditions, rather than relying on design claims alone.

Key challenges

  • Reducing high interface pressure at the heel, a common pressure ulcer site, across a wide range of patient body weights
  • Managing pressure at the sole-to-footboard interface, an easily overlooked contact point in supine positioning
  • Selecting an inflation setting that performs reliably without clinicians needing to factor in individual patient weight
  • Ensuring pressure-relief products do not compromise the skin microclimate, a known contributor to pressure damage

Our approach

Prolevo commissioned independent testing consultancy Duncan Bain Consulting to evaluate HeelSafe and SoleSafe using objective pressure mapping. HeelSafe was tested on the UCL Phantom, a life-sized articulated mannequin with soft tissue and heated, temperature-controlled skin, across six body weights, three inflation settings, and both flat and knee-flexed positions, benchmarked against a Softform Premier mattress and a domestic (Sealy Pearl Contour) mattress. Side-lying heel pressure was mapped using a live subject, since this position is too biomechanically complex to model with a phantom. SoleSafe was evaluated separately with a live subject and an XSENSOR pressure-mapping array, comparing a bare bed footboard against SoleSafe at two inflation settings, with 10 repeated measures used to establish 95% confidence intervals.

Approach summary

  1. Commission an independent pressure-mapping evaluation from Duncan Bain Consulting
  2. Test HeelSafe on the UCL Phantom across six body weights (40–200kg), three inflation settings, and flat and knee-flexed positions
  3. Map side-lying heel pressure, and sole-to-footboard pressure for SoleSafe, using a live subject with repeated XSENSOR measures
  4. Benchmark against a Softform Premier mattress, a domestic mattress and a bare bed footboard
  5. Assess heat and water vapour transfer through HeelSafe to check for any effect on skin microclimate

Outcomes and value

Across all body weights and positions tested, HeelSafe produced lower peak heel interface pressure than either comparator mattress, and a single mid-range inflation setting worked well regardless of patient weight. SoleSafe substantially reduced peak plantar pressure at the footboard compared with a bare board, with the higher of its two settings performing best.

HeelSafe

Simple optimum settingLower pressure than both mattressesConsistent across positionsMicroclimate unaffected
The middle (20 mmHg) inflation setting gave the lowest peak heel pressure in most conditions across body weights of 40–200kg, so weight need not be checked before inflatingPeak heel interface pressure with HeelSafe was lower than on both the Softform Premier and the Sealy Pearl Contour domestic mattress, across all body weights testedLower interface pressures were seen with knee flexion, and the mid-range setting remained optimal in the side-lying position tooHeat and water vapour transfer rates were within expected norms, with no adverse effect on skin microclimate foreseen versus existing mattresses

SoleSafe

Substantial pressure reductionHigher setting more effective
Mean peak plantar interface pressure fell from around 140 mmHg on a bare footboard to around 55 mmHg with SoleSafe at 20 mmHg inflationThe 20 mmHg setting outperformed the 10 mmHg setting, based on 10 repeated measurements with 95% confidence intervals

Study conclusion

The report concludes that HeelSafe provides effective heel pressure reduction across all body weights tested, relative to both comparator mattresses, with the mid inflation setting recommended as a simple, weight-independent default and no adverse effect on skin microclimate expected. SoleSafe was found to significantly reduce peak sole-to-footboard pressure, particularly at the higher of its two inflation settings.

Paraphrased from the conclusions, Evaluation of Prolevo HeelSafe & SoleSafe Pressure Redistribution Pads, Duncan Bain Consulting (report date not stated)

Study limitations to note

  • The report was commissioned by TalarMade trading division, and is a commercial evaluation rather than an independently peer-reviewed publication
  • Side-lying heel pressure and all SoleSafe results are based on a single live subject (a 71-year-old, 62kg female), so findings should be confirmed across a wider participant sample
  • No publication date is stated in the source document; its currency should be checked before citing it externally

Related support

You may also be interested in:

Request the full HeelSafe & SoleSafe evaluation report
Contact the TalarMade team

Share this

Not sure where to start?

Whether you are looking for a product, clinical service, professional support or general guidance, the TalarMade team can help point you in the right direction.